South Wales Steel Buildings

Grain stores in South Wales

A grain store is the one farm building where the walls carry a load from the inside. Tell us what you need to hold and you get engineered drawings and a price for the building, with the sum for its capacity worked from your own grain and the quantities for the floor it stands on.

What it holds
Area × depth × SW
Specific weight in kg/hl, divided by a hundred, is tonnes per m³.
Slab
200 mm
Sized for the loader working in it, not for the grain.
Drier fuel
Bunded
Any tank over 200 litres, under the Welsh oil storage rules.
Planning
Prior notification
Up to 465 m² on a unit of 5 hectares or more.

What you are actually buying

Most farm buildings keep the weather off something that stays put. A grain store has to contain a crop that presses outward along every metre of wall, so the retaining walls, the frame and the slab are designed as one structure from the start. Get that right and it is a simple building; get it wrong and the walls move.

Floor area follows from the tonnage

Decide what you need to hold and how deep you can fill, then let the floor area come out of the sum. A building chosen first and filled afterwards is usually too small by the second good harvest.

Wall height sets the depth of grain

Each extra metre of retaining wall adds capacity across the whole floor, which makes depth the cheapest tonnage available. It is also the dimension the engineer has to design for, because the pressure on the wall grows with it.

Eaves height is for filling the corners

Leave room above the walls for a loader bucket at full reach, or for the conveyor and spout if it is filled mechanically. Skimp here and the corners of the store never get filled.

What you get asked to decide

  • Precast concrete panels or a poured retaining wall, and the fill depth they are designed for
  • A drying floor with ducts formed in the slab, laterals on the surface, or no drying at all
  • Where the drier's fuel tank and its bund go, planned with the building
  • The tipping end, and doors wide and high enough for a loaded trailer or lorry
  • Proofing against birds and vermin at the eaves, the ridge and the doors
  • Supplied and erected, or supplied for your own team to put up

There is one more choice underneath all of those: whether the frame is cold rolled or hot rolled. It changes the price, the lead time, whether you can put it up yourself, and what goes in the ground.

How it goes from here

Five steps, in this order. The fourth is the one nobody prices for you up front, which is why there is a calculator further down this page.

  1. Step 1

    Tell us roughly what you need

    Span, length and what it is for. Approximate is fine — nobody expects you to have decided, and it means the first reply can be useful rather than a list of questions.

  2. Step 2

    Drawings and a price for the frame

    The manufacturer prepares engineered drawings and quotes the building. That includes the pad foundation sizes, which no calculator can work out for you.

  3. Step 3

    Settle the planning position

    Prior approval on a qualifying agricultural holding, or a full application. Worth establishing before steel is ordered rather than after.

  4. Step 4

    Get the base in

    Site strip, level, stone and slab, ready and cured before the erectors arrive. This is the part you can price on this page today.

  5. Step 5

    Delivery and erection

    Delivered for your own team to put up, or supplied and erected. Both are normal; the difference is worth asking about at quote stage, not later.

Get a price for my grain store

Rough dimensions are enough to start. You get a reply the same day.

Grain in South Wales

Wales grows little grain by the standards of eastern England. The Welsh Government's Survey of Agriculture and Horticulture, June 2025 puts cereals at around 3 per cent of farmland, but the area grew by 10 per cent in a year, mostly wheat. In the south the most arable land is the flat, limestone country of the Vale of Glamorgan; elsewhere a grain store often sits on a mixed holding among the livestock buildings.

That shapes the building. On a mixed holding a grain store can be one bay of a wider shed rather than a barn of its own, and in a wet harvest a drier is often part of it, which means a fuel tank. Both of those change what has to be designed, and the second brings in a set of Welsh rules.

Walls that hold the harvest in

Machinery, bales and livestock stand where they are put. A bulk of grain presses outward against whatever contains it, and it does so along the whole length of the wall. That is why a flat store has retaining walls designed for the depth of grain behind them, and why the walls, the frame and the floor are specified together as one structure.

Precast concrete panels and poured retaining walls are both used. Which one, how thick and how high all follow from the depth you want to fill to, and the pressures are worked out to Eurocode 1, Part 4, the design standard for silos and tanks. That is the engineer's job, and it is part of the drawings you get.

Loaded from inside

Side rails and sheeting on a machinery shed are there to keep the weather out. Heap grain against them and they bend, and the column bases start to move.

If the plan is to store grain in a building you already own, ask an engineer before you book the trailers. The frame is either checked and strengthened for it, or a retaining wall that stands on its own is built inside.

How much it holds, from your own grain

The sum is floor area, times the depth you fill to, times the density of the grain. You do not need a table for the density. The specific weight on your merchant's ticket is in kilograms per hectolitre; a hectolitre is a tenth of a cubic metre, so divide by a hundred and it is in tonnes per cubic metre.

Take a store 15 metres across and 30 long, filled level to 3 metres, holding grain that weighed 76 kg/hl. That is 450 square metres, times 3, times 0.76: about 1,026 tonnes. Raise the walls by a metre and the same floor holds about 1,368. Depth is the cheapest capacity there is, which is exactly why the wall height has to be designed, not stretched.

Do the sum backwards. Start with the tonnage you need to hold, choose the depth, and let the floor area follow. A store sized the other way round is how a heap ends up outside under a sheet in a wet October.

The drier's fuel tank, under Welsh rules

Farm fuel oil in Wales comes under the Water Resources (Control of Pollution) (Oil Storage) (Wales) Regulations 2016, the same rules as any business's tank, enforced by Natural Resources Wales. They apply to any container above ground holding more than 200 litres, indoors or out: a fixed tank, a drum, an IBC or a bowser.

The container has to sit in a bund. For one tank the bund holds at least 110 per cent of it; with several, the greater of 110 per cent of the largest or 25 per cent of them all. No valve or pipe may drain the bund, and the valves, filters, gauges and vent must be inside it. Plan the tank's position and its bund with the building, not after it.

Tank sellers often say it must be 10 metres from surface water and 50 metres from a borehole. The Welsh Government's guidance treats those distances as good practice where they can be kept, not as law — but keeping them is still the sensible choice next to a stream. If oil does escape, ring Natural Resources Wales on 0800 807060.

The floor is for the loader

Spread across a floor, grain is an easy, even load. The slab is sized for the telehandler: a full bucket, a tight turn, the same few spots day after day. That puts a grain store at 200 mm with mesh, the same as a machinery store and heavier than a hay barn.

A drying floor changes the pour rather than the thickness. The ducts are laid out for the way the store will be filled and emptied, and formed when the concrete goes in. Cutting them into a finished slab is slow, dusty and never as good.

A roof that keeps the crop dry from above

Moist air rises off a bulk of grain into the roof space. Where it touches cold, uninsulated sheeting it turns to water and drips back onto the heap — and damp on the surface of the heap is what gets a load turned away at the mill.

The answer is chosen with the cladding: sheets with an anti-condensation backing or an insulated panel, and ventilation so the roof space can breathe. Birds and vermin are the same kind of decision, settled at the eaves, the ridge and the door seals, and they are what an assurance inspection looks at.

Planning for a grain store in Wales

A store for grain grown on the holding is agricultural development. On a unit of 5 hectares or more it can usually go through prior notification: the council has 28 days to say whether it wants to approve the siting, design and appearance. The building must not exceed 465 square metres — and that count includes other buildings, plant and tanks put up on the unit within 90 metres in the previous 2 years, the drier's fuel tank among them. Beyond that, it is a full planning application.

Storing other farmers' grain as a business is a different matter, because the rights attach to agriculture on your own unit. Say so plainly at the start rather than find out later.

In Wales, farm buildings get their permitted development rights from Part 6 of the 1995 General Permitted Development Order, which splits at 5 hectares — and the two halves are not the same right with different numbers on them.

On a unit of 5 hectares or more, Class A permits a new building, or the extension or alteration of one, if it is reasonably necessary for agriculture on that unit. Its ground area cannot exceed 465 square metres — counted together with anything else put up on the unit within 90 metres in the previous 2 years. It must be no more than 12 metres high and at least 25 metres from a trunk or classified road. England's limits are far larger; they do not apply here.

On a unit of 0.4 to under 5 hectares, Class B does not let you put up a new building at all. It permits a limited extension or alteration of a farm building you already have — no taller, no more than 10 per cent more volume, and no more than 465 square metres in all. With four hectares and nothing to extend, a new shed is a full planning application.

Where Class A applies, you are not applying for planning permission. You notify the council, which has 28 days to decide whether it wants to approve the siting, design and external appearance. You can start when it says it does not, when it approves them, or when 28 days pass without a reply — provided the building genuinely is permitted development in the first place.

One exclusion catches people: no building for livestock, and no slurry or sewage sludge store, within 400 metres of the curtilage of a protected building — broadly, a house that is not part of your own farm.

Two more things are Welsh. Construction of 100 square metres or more needs its drainage approved by the SuDS Approval Body even when it is permitted development. And in a National Park the park authority is the planning authority — here, the Bannau Brycheiniog National Park Authority or the Pembrokeshire Coast National Park Authority.

A summary, not planning advice. The legislation is SI 1995/418, Schedule 2, Part 6 as in force in Wales, checked against legislation.gov.uk on 23 September 2026. The full rules are on our planning guide for farm buildings in Wales. Confirm your own position with the authority that covers your site.

Work out the base for your grain store

The calculator opens at the grain store slab. It gives you the quantities for the strip, the stone and the concrete under the building, to take to a groundworker for a price. The retaining walls and any drying floor are separate, and both are designed, not estimated.

Building

Loader traffic, and stored grain pushing against the walls.

m
m

Slab

Set by the building type above. Change it if you know different.

mm

Each side. Leave at 0 if it finishes flush.

mm

Site

mm

High corner to low corner.

Balanced keeps the dug material on the plot and moves the least.

mm

Dig a trial hole and measure it. This shifts more muck than the slope does.

Concrete to order for the slab
52.0m³waste allowed, rounded to the half metre
Grain store · slab 246.4 m² at 200 mm · working platform 352.6 m²
Ready-mix plant
Slab concrete
Net 49.3 m³ before waste
52.0m³
Quarry
Type 1 sub-base
Spread 188 mm loose to finish at 150 mm compacted
77.6t
Builders merchant
Mesh sheets
2.4 × 4.8 m sheets, 300 mm laps allowed
28sheets
Damp proof membrane
Laps and upstand included
276m²
Edge detail
Perimeter, for edge insulation or expansion joint
64.8m
Earthworks
Topsoil to strip
110.2 m³ once dug and loose
88.2m³
Cut
17.6m³
Fill
17.6m³

What this does not work out: the pad foundations

The concrete pads the stanchions sit on are sized by a structural engineer, not by a formula. They change with the span, the eaves height, the wind loading on your particular site and what the ground will bear. Anyone quoting you a pad size without a design has guessed it.

Want this priced properly?

Send us the job and we'll get you engineered drawings and a quote for the frame — with the pad sizes this tool can't work out. The figures above go with your enquiry, so you don't have to type them again.

Every enquiry gets a reply the same day, and your figures go with it. The building itself is designed and priced by South West Steel Buildings, our building partner, so your details go to them too, and they will be in touch. How we handle your details.

Common questions

How do I work out how much grain a store will hold?
Multiply the floor area by the depth you will fill to, then by the density of your own grain — and you already have that figure. The specific weight on the merchant's ticket is in kilograms per hectolitre; divide it by a hundred and you have tonnes per cubic metre. A 15 by 30 metre store filled level to 3 metres, with grain at 76 kg/hl, holds about 1,026 tonnes. Grain packs down a little in a deep bulk, so the real figure comes out slightly higher, never lower.
Is it safe to put grain against the walls of an ordinary shed?
Not until an engineer has said so. A bulk of grain pushes sideways on whatever holds it in, and the rails, sheets and column bases of a shed built for machinery were never designed to be loaded from inside. Either the frame is checked and strengthened, or a free-standing retaining wall goes in that carries the load itself. The design standard for pressures from stored grain is Eurocode 1, Part 4, on silos and tanks.
Does the drier fuel tank need a bund in Wales?
Yes, if it holds more than 200 litres, and so does a drum or a bowser of that size. Wales moved farm fuel oil into its general oil storage rules, so a farm tank is treated like any business's: a bund holding at least 110 per cent of the tank, no drain valve through the bund, and the valves and gauges inside it. The distances from water and boreholes that tank sellers quote as law are, in the Welsh Government's guidance, good practice where it can be managed.
Why does condensation drip off a grain store roof?
Air rising off the grain carries moisture into the roof space. When it meets a cold steel sheet it condenses and falls back onto the top of the heap, which is where a load gets rejected for moisture. The fix is chosen with the cladding — a sheet with an anti-condensation backing, or an insulated one, and a way for the roof space to breathe — and it costs little then and a great deal once the store is full.
What decides the thickness of the floor?
The machine, not the crop. Spread grain is a gentle, even load. A telehandler turning with a full bucket in the same few places every day is not, so a grain store floor is laid at 200 mm, the same as a machinery store and heavier than a hay barn. If a drying floor is wanted, its ducts are designed and formed in the pour; they cannot sensibly be cut in afterwards.
Do I need planning permission for a farm building in Wales?
It depends first on the size of the holding. On an agricultural unit of 5 hectares or more, Class A of Part 6 of the Town and Country Planning (General Permitted Development) Order 1995 permits a building reasonably necessary for agriculture on that unit, up to 465 square metres — counted together with anything else put up on the unit within 90 metres in the previous 2 years. It must be no more than 12 metres high (3 metres within 3 km of an aerodrome), at least 25 metres from a trunk or classified road, and a livestock building or slurry store must be at least 400 metres from a protected building. Before building you notify the council, which has 28 days to say whether it wants to approve the siting and design. On a unit of 0.4 to under 5 hectares Class B allows only a limited extension or alteration of an existing building, and a new building needs full planning permission; under 0.4 hectares there are no agricultural permitted development rights at all. England's larger limits do not apply in Wales.
Does a farm building in Wales need SAB approval?
If it covers 100 square metres or more and affects how rain soaks into the ground, yes — even when it is permitted development and needs no planning application. Since January 2019 construction of that size in Wales needs approval of its surface water drainage from the SuDS Approval Body, which is run by your local council, before work starts. Farm roofs and clean yards are included, and the rainwater off a new roof is usually the whole question.
Can I convert a farm building to a house in Wales without planning permission?
No. England has a permitted development right, Class Q, that lets some agricultural buildings become homes through a prior approval application. Wales has no equivalent: a barn conversion in Wales needs full planning permission from the local planning authority. Much of what is written about barn conversions online is about England, so check which country it was written for before relying on it.

Other buildings we cover

Same approach on each: what the building is, how it gets sized, where you stand on planning, and what the base underneath it comes to.

Get a price for your grain store

Send us the tonnage you need to hold and how deep you want to fill it, and the building is sized from that. You get engineered drawings and a price, with the pad foundation sizes and the retaining walls designed in.